「Powder Coating Tips」の版間の差分
LeonoraMcswain (トーク | 投稿記録) (ページの作成:「<br><br>Trust All J's Powder Coating. A Veteran owned business to have your industrial parts, boat parts, motorcycle frame, or any other type of equipment powder coated....」) |
Isidra9687 (トーク | 投稿記録) 細 |
||
| 1行目: | 1行目: | ||
| − | <br><br> | + | <br><br>Let us finish what you started with a coating to enhance your product or project that adds the benefit of a tough, attractive, cost-effective finish with little or no impact to the environment.<br><br>Steve, the owner and sprayer, asked me not to write this review. And I wasn't going to until I realized the root of why I had a ridiculous experience with him was in fact his laziness and lack of attention to detail. He has no clue how to prep for powder coating and even less of a clue on how to deal with customers. I'm sure he does a good job with old fences and bicycle frames, but I seem to have found the limit to No Limit Powder Coating and it comes in the form of a VW wheel.<br><br>If you are having the same issue with multiple powders, move onto the gun. Lower the air pressure going to your gun. Position your gun further from the part, and try shooting the part by not directly aiming at the part, meaning try spraying diagonally in front of the part aiming about halfway off of the part. These methods have definitely helped me when using the Craftsman gun. The [http://Www.Usatoday.com/search/dual%20voltage/ dual voltage] gun would not help you in this case, lower kv's are better for multiple coats. Another possible issue may even be the gun is defective. However, we will rule that out as the last possible problem. <br><br>Use thermoplastic coatings for items you might eventually remold, and thermoset coatings for items that will remain essentially permanent. The main difference between thermoplastic and thermoset is the reversibility of the coat. Like their name implies, thermoset coatings cannot re-melt after undergoing an irreversible chemical bonding process. Conversely, thermoplastic coatings can remelt because no chemical process takes place.<br><br>I found the below powder which looks promising. At $15 for half a pound it is far more expensive than other powders but can get 2 pounds for $33 which would be more in line with other powders. Would like to hear from anyone else that has used this powder for the tumble method and how you felt about the results. Or if you have found other powders that give the look of a copper jacket.<br><br>If you enjoyed this write-up and you would such as to receive more info regarding [http://www.biegpapiernika.pl/forum/profile.php?id=21628 spawanie] kindly see our own site. |
2016年7月27日 (水) 01:12時点における版
Let us finish what you started with a coating to enhance your product or project that adds the benefit of a tough, attractive, cost-effective finish with little or no impact to the environment.
Steve, the owner and sprayer, asked me not to write this review. And I wasn't going to until I realized the root of why I had a ridiculous experience with him was in fact his laziness and lack of attention to detail. He has no clue how to prep for powder coating and even less of a clue on how to deal with customers. I'm sure he does a good job with old fences and bicycle frames, but I seem to have found the limit to No Limit Powder Coating and it comes in the form of a VW wheel.
If you are having the same issue with multiple powders, move onto the gun. Lower the air pressure going to your gun. Position your gun further from the part, and try shooting the part by not directly aiming at the part, meaning try spraying diagonally in front of the part aiming about halfway off of the part. These methods have definitely helped me when using the Craftsman gun. The dual voltage gun would not help you in this case, lower kv's are better for multiple coats. Another possible issue may even be the gun is defective. However, we will rule that out as the last possible problem.
Use thermoplastic coatings for items you might eventually remold, and thermoset coatings for items that will remain essentially permanent. The main difference between thermoplastic and thermoset is the reversibility of the coat. Like their name implies, thermoset coatings cannot re-melt after undergoing an irreversible chemical bonding process. Conversely, thermoplastic coatings can remelt because no chemical process takes place.
I found the below powder which looks promising. At $15 for half a pound it is far more expensive than other powders but can get 2 pounds for $33 which would be more in line with other powders. Would like to hear from anyone else that has used this powder for the tumble method and how you felt about the results. Or if you have found other powders that give the look of a copper jacket.
If you enjoyed this write-up and you would such as to receive more info regarding spawanie kindly see our own site.
