「利用者:Kncai464187」の版間の差分

提供: 先週の結果分析
移動先: 案内、検索
細
細
 
(同じ利用者による、間の293版が非表示)
1行目: 1行目:
−
Vehicles that are purchased new from the automobile great deal come outfitted with a common stock air filter that acts as a element of the overall air intake process. These stock air filters enable air to flow to the car's internal-combustion engine in order for the auto to run smoothly. Car owners who want to receive increased functionality from their motor vehicle may perhaps opt to exchange their car's typical airbox with an aftermarket cold air consumption.<br><br>Also observe that the peak horsepower level was lowered about 340 rpm, which is terrific as it's normally great to bring your peak energy down into a much more useable driving variety. The engine also produced 417.1 lb-ft of torque at 4,740 rpm, which equates to an improvement of 15.three lb-ft of torque, peaking at only 10 rpm far more then the stock configuration.<br><br>Our judges loved the Appearance of this cold-air, and most commented that MAC should have integrated a total, chromed-up inlet tube (we're absolutely sure one will be on the way.) Add in a great Worth and surprising overall performance gains, and we assume MAC has a winner with this low-cost kit.
+
The AFE stage two has gotten a bad rap mainly because of the air intake noise, AFE now presents the Stage 2 Lid to assistance cancel out that noise.<br><br>Holding the filter clean is important to efficiency of any filter. In buy to maximize the positive aspects of the K&N, the CravenSpeed Cold Air Consumption utilizes a smoked, poly-carbonate best that the two seals and protects whilst making it possible for rapid visual inspections for cleanliness. Then the massive issue was a single of the rubber tubes was also small. Either they chose the incorrect size when they packaged mine or they are all like this, I'm not sure which of those it was but it is a solvable concern. After some stretching I was ready to make it match.<br><br>The elbow coupler does touch the radiator hose due to the extension of the throttle body spacer. The hoses does their occupation, but you may well want to substitute the coolant hose as it was not an exact match with the stock clamp. I was leaking coolant, till I zip tied the hose to seal it wholly. One particular other challenge I encountered was the MAF screw places had been not an precise fit with the MAF sensor. I was ready to securely seat and seal the MAF on the MAF location with some operate.<br><br>The moment that is set in spot, you can change the tailpipe area to be centered in the bumper cutouts. Hold the unit the place it need to go and merely tighten down the flange bolts holding the 2 pieces together. Repeat for the other side and you're finished! Volant Ram Filter: Cleanable and reusable large grade filter media reduces air restriction and increases engine output. Precision pleat geometry optimizes airflow all through the intake technique. If you don't have a tuner, pick out from the leading menu under EFILive or your vehicle yr and Programmers : Modules : Chips.<br><br>Went with the simple and simple cold air intake design from Roush. Set up was a breeze, took about 25 minutes. Quickly could hear a distinction in exhaust note and the throttle response improvements.....acceleration appears a great deal smoother. Ideal bang for the buck if you do not want a cold air that deviates from a clean factory seem beneath the hood.

2016年7月25日 (月) 22:38時点における最新版

The AFE stage two has gotten a bad rap mainly because of the air intake noise, AFE now presents the Stage 2 Lid to assistance cancel out that noise.

Holding the filter clean is important to efficiency of any filter. In buy to maximize the positive aspects of the K&N, the CravenSpeed Cold Air Consumption utilizes a smoked, poly-carbonate best that the two seals and protects whilst making it possible for rapid visual inspections for cleanliness. Then the massive issue was a single of the rubber tubes was also small. Either they chose the incorrect size when they packaged mine or they are all like this, I'm not sure which of those it was but it is a solvable concern. After some stretching I was ready to make it match.

The elbow coupler does touch the radiator hose due to the extension of the throttle body spacer. The hoses does their occupation, but you may well want to substitute the coolant hose as it was not an exact match with the stock clamp. I was leaking coolant, till I zip tied the hose to seal it wholly. One particular other challenge I encountered was the MAF screw places had been not an precise fit with the MAF sensor. I was ready to securely seat and seal the MAF on the MAF location with some operate.

The moment that is set in spot, you can change the tailpipe area to be centered in the bumper cutouts. Hold the unit the place it need to go and merely tighten down the flange bolts holding the 2 pieces together. Repeat for the other side and you're finished! Volant Ram Filter: Cleanable and reusable large grade filter media reduces air restriction and increases engine output. Precision pleat geometry optimizes airflow all through the intake technique. If you don't have a tuner, pick out from the leading menu under EFILive or your vehicle yr and Programmers : Modules : Chips.

Went with the simple and simple cold air intake design from Roush. Set up was a breeze, took about 25 minutes. Quickly could hear a distinction in exhaust note and the throttle response improvements.....acceleration appears a great deal smoother. Ideal bang for the buck if you do not want a cold air that deviates from a clean factory seem beneath the hood.

「http://ittai.net/mw/index.php?title=利用者:Kncai464187&oldid=252620」から取得