0
回編集
差分
細
編集の要約なし
Cork flooring tiles are made in 12-inch squares and they are mounted on towards the sub-surface with flooring adhesive. They can be installed directly onto concrete slabs or higher secure wood sub-flooring. Some flooring manufacturers recommend hardboard for glue-down installations, so make sure to you follow your manufacturer?s advice.<br><br><br><br>Regardless in of the sub-surface, the preparation requirements are similaris the same. The sub-surface have to be clean, dry, smooth and level. The following information provides some typical steps involved with sub-surface preparation of concrete slabs and wood sub-flooring.<br><br><br><br>Preparation for installation on concrete:<br><br><br><br>* Patch any cracks or holes per your flooring manufacturer?s recommendations<br><br><br><br>* Check the concrete for moisture content<br><br><br><br>Note: test methods vary; follow your manufacturer?s recommendation<br><br><br><br>* Cut the bottom of door frames enough allowing to allow for tiles to match underneath<br><br><br><br>* Make sure the concrete is clean, dry, smooth and level ahead of beginning the installationNote: having using a smooth sub-surface is critical essential for glued-down tiles ? the design contour of imperfections inside the concrete or loose debris left behind out will be seen and felt in the inside finished surface<br><br><br><br>* Apply sub-floor primer to for the concrete which has a roller and enable invite to dry just before applying adhesive<br><br><br><br>Preparation for installation on wood or hardboard:<br><br><br><br>* Repair any uneven areas<br><br><br><br>* Check moisture content of in the sub-floor according towards to the manufacturer?s recommendations<br><br><br><br>* If sub-flooring has ended is over a crawlspace, cover the floor [https://www.google.com/maps/d/u/1/viewer?mid=1zEmBTav-PhlDVZhQvSD99hx2Uwg&hl=en_US&authuser=1 hardwood Boston] bottom below the sub-floor with polyethylene sheeting<br><br><br><br>Note: most manufacturers recommend 6-mil sheets overlapped and taped together<br><br><br><br>* Cut the bottom of door frames enough to allow for tiles to match underneath<br><br><br><br>* As with concrete, make sure ensure the sub-floor is level, clean and most significantlyof all, smooth to prevent avoid any irregular shape transfer over the cork<br><br><br><br>* Apply sub-floor primer with having a roller and invite to dry ahead of before applying adhesive<br><br><br><br>Acclimation:<br><br><br><br>* Most manufacturers recommend acclimating cork tiles for 2-3 days, at normal-living temperature and humidity levels, and inside room the location where place that the tiles will likely probably be installed<br><br><br><br>Note: refer to your flooring manufacturer?s documentation for specific details<br><br><br><br>* Apply the recommended adhesive to on the sub-floor using having a roller, employed doing work in small areas at the same a time, and allow it to dry<br><br><br><br>Installation of tiles:<br><br><br><br>* Since cork has natural variations in shade and pattern, sort over the boxes and select tiles which that will provide the best overall look<br><br><br><br>* Using spacers, leave an expansion space around the border with of the room and around any fixed objects, like pipes and kitchen islands<br><br><br><br>Note: refer to reference your manufacturer?s instructions since expansion space recommendations can may differ from 1/4 in. to 1/2 in.<br><br><br><br>* Apply pressure equally through the surface of each tile because as it is laid in place<br><br><br><br>* After all tiles will be have been in [https://www.google.com/maps/d/u/1/viewer?mid=1zEmBTav-PhlDVZhQvSD99hx2Uwg&hl=en_US&authuser=1 hardwood Boston MA] place, and ahead of before applying sealer, roll the complete entire floor according for to the manufacturer?s recommendations<br><br><br><br>* Allow the adhesive to dry completely before walking for on the floor<br><br><br><br>Note: the typical normal recommendation is twenty four 24 hours, but this may vary according to based on climatic conditions<br><br><br><br>* Clean the finished floor using having a polyurethane cleaner then seal it with a urethane sealer, as recommended through by the manufacturer<br><br><br><br>Always follow your flooring manufacturer?s recommendations and the end result will likely probably be a beautiful new cork floor that you?ll be proud to show off for many yearsa long time.<br>Tony Cuozzo is the co-founder of FastFloors.com the worldglobe?s best online source for flooring products. Find out more about several types a variety of flooring materials, installation instructions, design tips, suggestions about advice on care and maintenance, and data information about individual manufacturers as well as their products, offered at: =>